/testing/guestbin/swan-prep ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ip tunnel add test0 mode gre local 192.1.2.45 remote 192.1.2.23 ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ip addr add 172.29.1.1/24 dev test0 ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ip link set dev test0 up ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ipsec start Redirecting to: namespaces direct start via ipsec pluto ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# /testing/pluto/bin/wait-until-pluto-started ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ipsec auto --add test1 002 "test1": terminating SAs using this connection 002 added IKEv1 connection "test1" ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ipsec auto --add test2 002 "test2": terminating SAs using this connection 002 added IKEv1 connection "test2" ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ipsec auto --add test3 002 "test3": terminating SAs using this connection 002 added IKEv1 connection "test3" ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# # should establish ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ipsec auto --up test1 002 "test1" #1: initiating IKEv1 Main Mode connection 102 "test1" #1: sent Main Mode request 104 "test1" #1: sent Main Mode I2 106 "test1" #1: sent Main Mode I3 002 "test1" #1: Peer ID is ID_IPV4_ADDR: '172.29.1.2' 004 "test1" #1: IKE SA established {auth=PRESHARED_KEY cipher=AES_CBC_256 integ=HMAC_SHA2_256 group=MODP2048} 002 "test1" #2: initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS+UP+IKEV1_ALLOW+IKE_FRAG_ALLOW+ESN_NO {using isakmp#1 msgid:b70508f9 proposal=defaults pfsgroup=MODP2048} 115 "test1" #2: sent Quick Mode request 004 "test1" #2: IPsec SA established tunnel mode {ESP=>0x5d7990e6 <0x5aba6cdc xfrm=AES_CBC_128-HMAC_SHA1_96 NATOA=none NATD=none DPD=passive} ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ip addr add 172.29.1.3/24 dev test0 ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ipsec auto --ready 002 listening for IKE messages 002 adding UDP interface test0 172.29.1.3:500 002 adding UDP interface test0 172.29.1.3:4500 003 two interfaces match "test2" (test0 172.29.1.3, test0 172.29.1.1) 002 "test2": terminating SAs using this connection 002 forgetting secrets 002 loading secrets from "/etc/ipsec.secrets" ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting]# ipsec auto --up test2 022 "test2": we cannot identify ourselves with either end of this connection. 172.29.1.1 or 172.29.1.3 are not usable 036 failed to initiate test2 ]0;root@swantest:/home/build/libreswan/testing/pluto/basic-pluto-09-orienting[root@west basic-pluto-09-orienting 36]# >>>>>>>>>>cutnonzeroexit>>>>>>>>>> exit status 36 3-west-run.sh 'ipsec auto --up test2' <<<<<<<<<>>>>>>>>>cut>>>>>>>>>> done <<<<<<<<<